• For professional use only!
• BEFORE USING, READ AND UNDERSTAND ALL LABEL INSTRUCTIONS AND MATERIAL SAFETY DATA SHEETS.
• For technical advice call our Loba-Wakol Technical Service at 1-800.230.6456.
• Recommended conditions are 55°F-80°F/40-75%rH.
• Sand and prepare floors according to NWFA guidelines.
• WARNING! If you scrape, sand, or remove old paint from wood floors, you may release lead dust. Follow local and/or federal requirements for lead removal. Before you start, find out how to protect yourself and others by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
• ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE, AND DESIRED RESULTS.
• POT LIFE: 2 hours. For mixing the full container shake base well, and add complete hardener to base, replace lid, and then shake vigorously to mix. For mixing smaller quantities, mix at a ratio of 10 parts base : 1 part hardener. Use the LOBA Mixing Container or a scale to weigh out the components.
• Do not thin. Do not add water.
• Do not apply at temperatures below 55°F (13°C). Make sure material is at room temperature. Always maintain adequate ventilation during all phases of the coating and drying process.
• Apply evenly at the recommended coverage rate. Avoid streaks, puddles, and lap marks.
• This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol wood flooring adhesives may be found in the "Connected Systems Matrix": https://www.loba.de/us/connected-systems/

Application Tool

LOBA Roller Deluxe 120 - as a two coat system.
LOBA Roller Microfiber 100-120 - as a three coat system ONLY.
NOTE: Alternate applicators could apply less finish and will have an increased risk of application marks and are not recommended

Coverage

LOBA Roller Deluxe 120: apply at 325-375 square feet per gallon per coat.
LOBA Roller Microfiber 100/120: apply at 400-500 square feet per gallon per coat.

Drying time

• Earliest possilbe recoating after 4-6 hours.
• Fully cured after 5 days.

Recommended procedure for 2 coat application:

• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• Allow to dry for 4-6 hours minimum.
• Intermediate sanding with LOBASAND 180 grit perforated pad (or equivalent) to remove grain raise.
• Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• NOTE: An optional third coat can be applied using the LOBA Roller Deluxe 120 and the procedures listed below for a 3 coat application can be followed.

Recommended procedure for 3 coat application using the LOBA Microfiber 100-120 roller:

• Apply 2K InvisibleProtect using the LOBA Roller Microfiber 100-120.
• Allow to dry for 2-4 hours minimum.
• Apply 2K InvisibleProtect using the LOBA Roller Microfiber 100-120.
• Allow to dry overnight.
• Intermediate sanding with LOBASAND 180 grit perforated pad (or equivalent) to remove grain raise.
• Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust. Apply 2K InvisibleProtect using the LOBA Roller Microfiber 100-120.

Alternative procedure to create natural oiled color:

• Prime with 2K Intensive Transparent refer to the Technical Data Sheet for details.
• Allow to dry for 16 hours minimum.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• Allow to dry for 2-4 hours minimum.
• Note: If intermediate sanding is required allow first coat to dry overnight.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.

Alternative procedure to create natural oiled color:

• Prime with 2K Intensive Transparent. Refer to Technical Data Sheet for details.
• Allow to dry for 16 hours minimum.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• Allow to dry for 2-4 hours minimum.
• Note: If intermediate sanding is required allow first coat to dry overnight.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.

Recommended Procedure for cork floors:

Seal cork only after the glue has sufficiently set (refer to manufacturer’s information) Roll on a maximum of 2 coats per day.

Untreated natural cork:

• Roll a total of three coats of 2K InvisibleProtect onto the cork.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• Allow to dry for 2-4 hours
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• Intermediate sanding with LOBASAND 180 grit perforated pad (or equivalent) to remove grain raise
• Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
  

Prefinished cork:

Note information given by the cork supplier. If suitable for recoating, apply one or two layers of 2K InvisibleProtect Follow instructions above for Screen and Re-Coat. If the factory applied finish is a UV cured, oxided containing, finish, application of LOBA 2K Contact will be required for preparation and LOBA 2K InvisibleProtect should not be used.

Renovation / recoating of old coatings:

• Cleaning with LOBA Remover at a ratio of 1:5. Use a rotary disk buffing machine and a LOBASAND SpecialPad green. Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralize). After drying, perform a thorough intermediate sanding with LOBASAND 180 grit perforated pad (or equivalent). Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
• Apply Apply 2K InvisibleProtect in one or two layers using the LOBA Roller Deluxe 120.

Suitable product combinations

Suitable sealers:

A sealer is not required, however, 2K Invisible Protect can be applied over all LOBA sealers, finishes, and LOBA Stain.

Screen and Recoat

• Clean floor, abrade with LOBASAND 180 grit perforated pad (or equivalent). Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
• Apply finish following instructions.
• Always prepare test areas to determine compatibility, appearance, and desired results.

• Do NOT use on floors finished with UV cured, oxide containing, factory applied finishes.

For professional use only!

Compatibility

When this product is used in combination with other LOBA products the technical information of these products must be followed. Refer to the Technical Data Sheets. LOBA cannot guarantee the suitability of products other than LOBA.