• For professional use only!
• BEFORE USING, READ AND UNDERSTAND ALL LABEL INSTRUCTIONS AND MATERIAL SAFETY DATA SHEETS.
• For technical advice call our Loba-Wakol Technical Service at 1-800.230.6456.
• Recommended conditions are 50°F-80°F/40-65%rH.
• Sand and prepare floors according to NWFA guidelines.
• WARNING! If you scrape, sand, or remove old paint from wood floors, you may release lead dust. Follow local and/or federal requirements for lead removal. Before you start, find out how to protect yourself and others by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
• For best results the final sanding by screen should be 100 grit.
• ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE, AND DESIRED RESULTS.
• POT LIFE: 1 hour: Stir base well, add the hardener in a ratio of 10:1 and stir in well (also possible by machine with LOBA Paint mixer). If partial quantities are to be mixed, these must be weighed out.
• Do not thin. Do not add water.
• Do not apply at temperatures below 55°F (13°C). Make sure material is at room temperature. Always maintain adequate ventilation during all phases of the coating and drying process.
• Apply evenly at the recommended coverage rate. Avoid streaks, puddles, and lap marks.
• This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol wood flooring adhesives may be found in the "Connected Systems Matrix": https://www.loba.de/us/connected-systems/

Application Tool

LOBA trowelSingle disc machineLOBASAND SpecialPad beige

Coverage

150-250 square feet per per 0.75 kg unit for colored oil with 2 coats
Coverage depends on the absorbency of the wood.

Drying time

• • Walk on after 12 hours.
  • Slightly stressable after 24 hours.
  • Fully stressable after 10 days.

Trowel-Application One Day System

• Apply small quantity of 2K ImpactOil Color to the floor by using a LOBA Trowel.
• Allow the oil to penetrate for 20 minutes.
• Equalize the surface by using a buffing machine and a LOBASAND SpecialPad beige. Buff to remove excess and until you achieve a consistent and uniform color.
• Equalize the edges by hand using strips of a LOBASAND SpecialPad beige.
• Repeat process.
• Remove all footprints and residues with a buffer or by hand.
  

Pad-Application for Two Day System

• Put 2K ImpactOil Color directly onto a LOBASAND SpecialPad beige and distribute in a then even layer using a buffer.
• Equalize surface with buffer and new LOBASAND SpecialPad beige.
• Equalize the edges by hand using strips of a LOBASAND Special pad beige.
• Remove all footprints and residues with a buffer or by hand.
• After drying overnight repeat the procedure. You will find a detailed instruction to this topic in our Technical Tips and Tricks “Application technique of 2K ImpactOil by using a LOBASAND SpecialPad beige”.

Suitable product combinations

Optional pre-treatment to achieve special effects

Pigment stain:

• PreTone white.
  
• PreTone brown.
  
• PreTone black.
  
• PreTone mocha.
  
• PreTone steel.
  Refer to the Technical Data Sheets for the product.

Important information

WARNING! SELF-IGNITION:
Store cloths, pads, and other tools contaminated with oil in closed metal container or soak in water immediately after use. Do not leave used rags on jobsite! Do not dispose of with sawdust!For professional use only!

Compatibility

When this product is used in combination with other LOBA products the technical information of these products must be followed. Refer to the Technical Data Sheets. LOBA cannot guarantee the suitability of products other than LOBA or the bond of the existing coating to the substrate.