2K Intensive Transparent

Contact 2K Intensive Transparent | Loba

2K Intensive

- Transparent

High-Solid 2-component oil-based primer for wooden floors. Achieves an oiled optic underneath the finish due to a significant color reinforcement.

Properties

Significant deepening of the wood color
Cobalt and butanonoxime-free
Combines oiled look with the advantages of finished surfaces
Easy and safe application
No roughening of the wood
No side-bonding effect

Technical data sheets

2K Intensive Transparent

Further information

Range of use

Suitable for virtually all types of European and exotic timber. Note the LOBA wood types list, which can be found at www.loba.de. If in doubt, consult the factory. The side-bonding effect of Water-based finishes is reduced. No block bonding occurs with parquet or wooden flooring that has been properly laid and bonded or secured with shear-resistant adhesive.

Art.-no.
11053-000000-60-000	600 g	4	320
11053-000000-18-000	2.5 kg	4	120

Shake the masse, add the hardener in a ratio of 5:1 and mix in with LOBA Paint mixer by machine. For mixing smaller quantities, use the LOBA Mixing Container or a scale to weigh out the components. Can be used for two hour after mixing.
At site conditions of 50% rel. humidity or higher, it is important to ensure adequate air ventilation with fans.
The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% - 65%, material temperature +18°C - + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
Transfer material to a LOBA varnish bucket before applying.
Stir the material well.
Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.

Thinner / Mixing

The product is ready for use and must not be reduced!

Application tool / application rate

LOBA oil roller Microfaser 60-80 / approx. 20-40g/m² (25-50m²/kg) depending on the absorbency of the substrate.
Equalise with LOBASAND SpecialPad beige.

Drying time

Earliest possible overcoating after 12 hours.
If there are drying delays, wait until completely dry.

Intermediate sanding

Do not intermediate-sand the primer.

Structure recommendation for roller application:

Apply a thin layer of primer using the LOBA Oil roller "Microfiber 60-80".
After around 30-60 minutes contact time, thoroughly equalise using a single-disc machine and the LOBASAND SpecialPad beige, completely removing any excess.
Dry for at least 12 hours.
Apply LOBA Water-based finish (according to technical information).
Intermediate polish with a LOBASAND grid pad with P240 sanding stripes underneath.
Apply LOBA Water-based finish (according to technical information).

Suitable product combinations

Suitable finishes:

2K InvisibleProtect
2K Supra A.T.
2K Duo.
2K Fusion.
EasyFinish.

Important information

If the fibre saturation is not achieved due to an inadequate amount of product being applied, or if there is only a single trowel application, greying of the wood can occur.Excess material must be completely removed during equalisation. Drying delays are possible on some exotic timbers.Keep soaked cloths, pads and other tools in closed containers. Moisten oil in combination with sanding dust, fabric cloths and so on with water or store in a sealable bucket and dispose of in a fire-safe manner, since otherwise there is a risk of self-ignition.